7700/50 SF

Product Specifications | June 2017 78-5102-0254-8, Rev A 3M™ Round Conductor Flat, Controlled Impedance Cable, 7700 Series Scope This document summarizes test methods, test conditions, and product performance requirements for 3M™ Round Conductor Flat, Controlled Impedance Cable, 7700 Series. Reference Documents Note: Unless otherwise specified, latest edition of the reference documents applies. In the event of conflict between requirements of the references and 3M specification, 3M specification shall take precedence. 3M™ Round Conductor Flat, Controlled Impedance Cable, 7700 Series Literature Code / Document Number 78-5100-2667-9 78-9102-5431-3 EIA-364 Document Title Customer Drawing, Round Conductor Flat, Controlled Impedance Cable, 7700 Series, .025” Cable Cable Preparation Instructions for Round Conductor Flat, Controlled Impedance Cable, 7700 Series Commercial standards, specifications and report Regulatory Compliance Visit www.3M.com/regs for compliance information. See customer drawings for regulatory specifics on each connector. Performance Testing Unless otherwise specified, all tests performed using 3M cable 7700/20 at conditions per EIA-364. Unless otherwise specified, all values and limits are typical of those obtained by qualification testing of the subject product. All specifications are subject to revision and change without notice from 3M. The surface of the ribbon cable has a metallic appearance but is not conductive. There is a translucent polyester outer layer over an aluminum foil layer, which gives this appearance. The cable construction has a thin conductive layer at each edge, user should evaluate its use in their application and, if necessary, insulating tape may be applied to cover the aluminum layer, as user deems appropriate. 3M™ Round Conductor Flat, Controlled Impedance Cable, 7700 Series Materials Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. 3M™ Round Conductor Flat, Controlled Impedance Cable, 7700 Series Feature Conductors Material 30 AWG Solid, Tin Plated Copper Insulation Polyolefin Covering Aluminum & Polyester Ratings Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. 3M™ Round Conductor Flat, Controlled Impedance Cable, 7700 Series Feature Flame test rating Value FT2, Horizontal flame Voltage rating 30 V AC Operating temperature 80°C MAX Storage temperature -20°C to +80°C Electrical Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. 3M™ Round Conductor Flat, Controlled Impedance Cable, 7700 Series Description or Parameter Dielectric withstanding voltage Units Insulation resistance Mega ohms V DC Values / Limits 750 >1000 Requirement or Conditions Subject a voltage of 750 VDC for 1 minute at sea level between adjacent wires, between wire and covering, and covering to exterior of cable including cable edges. Covering pulled back 0.125” from cable end. Measured between adjacent wires, between wire and covering, and covering to exterior of cable including cable edges with 500 VDC applied for 1 minute. Test Standard or Method EIA-364-20 EIA-364-21 Product Specifications | 78-5102-0254-8, Rev A 3M™ Round Conductor Flat, Controlled Impedance Cable, 7700 Series Signal Integrity Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. 3M™ Round Conductor Flat, Controlled Impedance Cable, 7700 Series Description or Parameter Differential impedance Differential insertion loss Units Ohms Values / Limits 95 ± 5 dB < 3 typ. Diff-to-common mode conversion dB < -15 ps/m < 15 Intra pair skew Requirement or Conditions Rise time of 35ps. Measured on non-edge wires. Measured one meter length samples. Smooth curve remains above limit at 2.5 GHz. Measured on non-edge wires. Measured one meter length samples from 50 MHz to 6 GHz. Measured on non-edge wires. Measured one meter length samples with TDR method. Rise time of 35ps. Measured on non-edge wires. Test Standard or Method EIA-364-108 EIA-364-101 Mechanical Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. 3M™ Round Conductor Flat, Controlled Impedance Cable, 7700 Series Description or Parameter Critical dimension measurements Peel force Units Inches Lbf/conductor Values / Limits See related customer drawing 0.0204 ± 0.0075 Requirement or Conditions Measure dimensions specified by related customer drawing. Prepare sample by removing both edge conductors. Test Standard or Method Measured by 180° peel direction, no faster than 2” peeled per minute. Environmental Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Environmental test samples prepared using 1 meter samples in both flat and H-folded configurations. H-fold includes three 180° folds plus two 45° folds. Recommended bend radius of folds >0.075” 3M™ Round Conductor Flat, Controlled Impedance Cable, 7700 Series Description or Parameter Temperature life (thermal aging) Thermal shock Humiditytemperature cycling Units Degrees C Hours Degrees C Cycles Degrees C % RH Cycles Degrees C Values/ Limits 85 1008 -55 & 85 5 25 to 65 80 to 100% 24 -10, cold shock Requirement or Conditions No physical abnormalities. Meets SI requirements. No physical abnormalities. Meets SI requirements. No physical abnormalities. Meets SI requirements. Test Standard or Method EIA-364-17 Method A, Condition 3D EIA-364-32 Table 2, Condition I EIA-364-31 Condition B, Method III, Figure 1 Product Specifications | 78-5102-0254-8, Rev A 3M™ Round Conductor Flat, Controlled Impedance Cable, 7700 Series Figures Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Figure 1: Representative impedance profile Figure 2: Representative insertion loss curve Figure 3: Representative H-fold setup Product Specifications | 78-5102-0254-8, Rev A 3M™ Round Conductor Flat, Controlled Impedance Cable, 7700 Series Regulatory: For regulatory information about this product, contact your 3M representative. Technical Information: The technical information, recommendations and other statements contained in this document are based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed. Product Use: Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of a 3M product in a particular application. Given the variety of factors that can affect the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for user’s method of application. Warranty, Limited Remedy, and Disclaimer: Unless an additional warranty is specifically stated on the applicable 3M product packaging or product literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. If the 3M Product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price. Limitation of Liability: Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability. 3M Electronics Materials Solutions Division Interconnect Solutions 6801 River Place Blvd. Austin, TX 78726-9000 www.3M.com/Interconnect 3M is a trademark of 3M Company. Please recycle. ©3M 2017. All rights reserved. 78-5102-0254-8, Rev A Product Specifications | 78-5102-0254-8, Rev A